Usb Vid 1f3a&pid Efe8&rev 02 3 Driver May 2026

Look at your connected USB peripherals. Disconnect non-essential devices one by one while watching Device Manager refresh. Determine if the device is:

If you want a specific artifact (email, udev rule, Windows INF steps, or libusb sample), tell me which and which OS you’re using; otherwise I can assume Linux and provide an example.

The Hardware ID USB\VID_1F3A&PID_EFE8 identifies a device using an Allwinner SoC (System on a Chip) that has entered FEL mode. What is FEL Mode?

FEL is a low-level subroutine in the boot ROM of Allwinner processors (like the A10, A13, or R16). It is used for firmware recovery or initial programming via USB when the device cannot find a valid boot image on its internal storage. Driver Details & Compatibility

The "REV 02 3" (often seen as REV_02B3) refers to a specific revision of the device's firmware or hardware interface. USB Device(VID_1f3a_PID_efe8) Driver for System

This hardware ID identifies an Allwinner Technology device in FEL Mode, a special recovery and flashing state. It is commonly found on Android tablets, TV boxes, and single-board computers like the Orange Pi. Driver Identification Manufacturer: Allwinner Technology Co., Ltd. Device State: FEL Mode (Low-level BootROM recovery) Hardware ID: USB\VID_1F3A&PID_EFE8 Common Name: Allwinner USB Flash FEL Mode Driver Key Features

NAND/eMMC Flashing: Allows deep-level firmware updates or "unbricking" via tools like PhoenixSuit or LiveSuit.

BootROM Access: Communicates directly with the chip's internal bootloader before the OS starts.

Mass Storage Export: In some configurations, it can export the internal storage as a USB drive to a PC. usb vid 1f3a&pid efe8&rev 02 3 driver

Compatibility: Drivers exist for Windows XP through Windows 10 (64-bit). How to Install

If your computer shows this as an "Unknown Device," you typically need the WinUSB or Allwinner driver to communicate with it. Using Zadig (Recommended for Developers): Download the Zadig tool. Select Options > List All Devices. Choose the entry with VID 1F3A and PID EFE8. Select WinUSB and click Replace Driver. Manual Installation:

Download the driver package from a reputable source like DriverMax or DriverFiles.

Open Device Manager, right-click the device, and select Update Driver.

Choose Browse my computer for drivers and point to the folder containing the .inf file.

💡 Note: If you see this ID, your device is likely stuck in recovery mode or the "FEL" button is being held down.

Are you trying to flash new firmware or just get your computer to recognize the device for file transfers? h3-fel-mass-storage/README.md at master - GitHub

The hardware identifier USB\VID_1F3A&PID_EFE8 is primarily associated with Allwinner Technology devices. It typically appears when an Allwinner-based tablet, smartphone, or car head unit is in FEL mode (a low-level flashing/recovery mode). Driver Details Look at your connected USB peripherals

This driver is necessary for the computer to communicate with the device for firmware updates or flashing via tools like LiveSuit or PhoenixSuit. Manufacturer: Allwinner Technology. Common Version: 1.0.0.1 (released around 2013–2014).

Supported OS: Windows XP, 7, 8, 10, and 11 (both 32-bit and 64-bit). Where to Find the Driver

Because this is a specialized recovery driver, it is rarely available through Windows Update. You can typically find it in the following places:

Flashing Utilities: It is often bundled in the /Drivers folder of the LiveSuit or PhoenixSuit installation directories.

Driver Repositories: Third-party sites like Driver Scape and DriverMax host standalone versions of the 1.0.0.1 driver. How to Install

How to Find Vendor ID and Product ID for Your USB Device | Acroname

The hardware identifier USB\VID_1F3A&PID_EFE8&REV_02 refers to a specific low-level communication state for devices powered by Allwinner Technology processors. DeviceHunt The Backstory: "FEL Mode"

This driver is not for a typical consumer peripheral like a printer or mouse. Instead, it is the signature of an Allwinner device in "FEL Mode" The Trigger: If WinUSB does not work, you need the

A device (such as an Android tablet, TV box, or single-board computer) enters this mode automatically if it cannot find a valid boot image on its internal storage. The Purpose:

It acts as a "recovery" or "flashing" state. Once the device is in FEL mode and connected to a PC via USB, it reveals itself as VID_1F3A&PID_EFE8 The Action:

Technicians and hobbyists use this mode to upload new firmware, unbrick a "dead" device, or run low-level diagnostics using tools like the sunxi-tools Driver Details

If your Windows Device Manager shows an "Unknown Device" with this ID, it usually means your Allwinner-based hardware is waiting for instructions to boot or be flashed. Driver Scape Manufacturer: Allwinner Technology Common Version:

v1.0.0.1 (released circa 2013) is the standard legacy driver used for Windows XP through Windows 10/11. It serves as a bridge for software like PhoenixSuit to communicate with the processor's internal ROM. DeviceHunt When You’ll See It

You will likely encounter this driver in the following scenarios: Unbricking: Trying to fix a tablet that won't turn on past the logo. Development:

Uploading custom Linux kernels to Allwinner-based development boards. Accidents:

If a device's internal storage (NAND/eMMC) is corrupted, it may fall back to this mode, appearing to your computer as this specific USB ID. for an Allwinner device?

FEL mode repeatedly connects and disconnects. Is this normal? 13 Feb 2020 —

If WinUSB does not work, you need the manufacturer’s driver. Since Ours Technology does not publicly list this PID for consumers, try these sources: