Follow these steps methodically. Rushing or missing a step can cause the reset to fail.
Step 1: Enter Service Mode The printer must be placed into a special diagnostic mode. Turn off the printer. Then, while holding down the Stop/Reset button (the triangle inside a circle), press and hold the Power button. Keep holding the Power button, but release the Stop/Reset button. While still holding Power, press the Stop/Reset button twice (or five times, depending on the firmware—two times is standard). Then, release the Power button. The green power light will flash, then remain steady. The printer is now in Service Mode.
Step 2: Connect and Launch the Service Tool With the printer in Service Mode, open the downloaded service tool on your Windows computer. You may need to run it as an administrator (right-click the file and select "Run as administrator").
Step 3: Select the Correct USB Port In the service tool interface, click the "USB Port" button or dropdown menu to select your Canon G2010 from the list. If the printer does not appear, ensure the USB cable is securely connected and the printer is still in Service Mode.
Step 4: Reset the Waste Ink Counter In the service tool, locate the section labeled "Waste Ink Pad Counter" or "Absorber Counter." Click the "Main" checkbox. Some tools also have a "Platen" or "Borderless" checkbox—if available, select both. Then, click the "Set" or "Reset" button. A progress bar may appear, and after a few seconds, you should see a confirmation message such as "Set Successfully."
Step 5: Power Off and Test Close the service tool. Turn the printer off using the Power button. Wait 10 seconds, then turn the printer back on. The error lights should disappear, and the printer should function normally. Run a single nozzle check or print a test page to confirm operation.
Less common for the G2010 are hardware dongles. These devices intercept the signal between the printer and the PC or attach directly to the logic board. While common for cartridge chip resetting, the integrated nature of the G2010’s tank system makes software manipulation of the EEPROM the dominant method.
Before attempting a reset, it is important to understand why the printer stops. The Canon G2010 uses a built-in counter to track the amount of ink flushed into the absorbent waste ink pads during cleaning cycles and borderless printing. Once this counter reaches a predetermined limit, the printer locks itself to prevent an overflow that could leak ink inside the machine, causing damage. The error is a safety mechanism, not a malfunction. Consequently, resetting the counter does not physically clean or replace the pads; it only tells the printer’s memory that the pads are "empty" again.
While resetting the Canon G2010 is effective, it is not a permanent solution without physical maintenance. Each reset allows more waste ink to accumulate. Eventually, the pads will become physically saturated, leading to ink leakage inside the printer, which can stain surfaces and damage electronics. Therefore, after two or three resets, it is strongly recommended to either:
In summary, resetting the waste ink counter on a Canon G2010 is a straightforward process using a service tool, but it should be performed with an understanding of the underlying hardware limitations. By following the steps carefully—entering service mode, running the tool, and resetting the counter—you can quickly restore your printer to working order. However, responsible printer maintenance includes monitoring physical waste ink levels to prevent future damage. This combination of software reset and hardware awareness ensures your Canon G2010 continues to provide reliable, low-cost printing for years to come.
To reset a Canon G2010 printer, you can either perform a manual hardware reset
to clear waste ink counter errors (like 5B00 or P07) or use the on-device menu to initialize general settings. Manual Reset (Service Mode)
This method is used to fix the "Waste Ink Pad Full" error (5B00 or P07) without needing external software. Enter Service Mode Ensure the printer is turned off but connected to power. Press and hold the While holding Power, press the
Release both buttons. The green power light will flash and then stay steady. Reset the Waste Ink Counter Once in Service Mode (steady green light), press the to confirm the command.
The printer will process the reset and may print a page showing a "D" value of , indicating the counter is cleared. Exit Service Mode button to turn the printer off. Turn the printer back on; the error should be gone. Factory Reset (Device Settings) Use this for general connection or configuration issues. LCD Button Method Ensure the printer is on.
button (pliers/screwdriver icon) until "1" appears on the LCD. button repeatedly until the letter Press either the button to initialize all settings. Menu Navigation (if applicable) Device settings Reset settings Verification & Troubleshooting Check Counter Status : In Service Mode, you can press Stop 3 times Power once
to print the EROM data. The "D" value shows the current waste ink percentage. WIC Reset Utility : If manual steps fail, third-party software like the WIC Reset Utility
can be used, though it typically requires purchasing a "Reset Key". clean the print heads
if you are still experiencing print quality issues after the reset? AI responses may include mistakes. Learn more
The Canon PIXMA G2010 resetter refers to tools or procedures used to clear the internal "waste ink counter," which triggers errors like 5B00 or P07 when the printer's ink absorber pads are theoretically full. While the printer might stop functioning to prevent ink leaks, you can often resume printing by resetting these software limits. Understanding the 5B00 Error resetter printer canon g2010
This error occurs because the printer tracks every cleaning cycle and ink flush. Once the limit is reached, it displays an "Ink Absorber Full" message and locks the device. A resetter—whether a software utility or a manual sequence—tells the printer's motherboard that the counter is back to 0%. Method 1: Manual Button Reset (No Software Required)
You can often clear the 5B00 error using only the printer's physical buttons by entering Service Mode. Enter Service Mode: Turn off the printer completely.
Hold the Stop button (red triangle), then press and hold the Power button. While still holding Power, release the Stop button. Press the Stop button 6 times.
Release the Power button. The green light should flash and then stay steady. Reset the Counter: Once in Service Mode, press the Stop button 5 times. Press the Power button once to confirm the reset.
The printer will print a page showing the counter (D-value) is now D=000.0.
Finish: Turn the printer off and then back on to exit Service Mode. Method 2: Professional Software Resetters
If manual button sequences fail, specialized software can provide a deeper reset.
Canon Service Tool (V3400/V4720/V6310): These are technician-level tools used to interface with the printer via a USB cable. In the tool, you select Main under the "Absorber Clear Ink Counter" section and click Set.
WIC Reset Utility: A popular third-party tool available at WIC Reset
that requires a purchased "Reset Key". It is often preferred for its user-friendly interface and support for Windows and macOS systems. Hardware Resetter: Devices like the MC-G02 Chip Resetter Go to product viewer dialog for this item.
are used for newer G-series models that use maintenance cartridges with chips, allowing you to reset the chip's memory without replacing the unit. Method 3: Resetting Ink Levels After Refill
If your printer isn't throwing an error but is flashing a low ink warning after you've refilled the tanks, you need an ink level reset.
Initialization: Press the Setup button, then use the + button until "C" appears on the LCD. Press Black or Color to initialize the settings.
Bypass Warning: Alternatively, press and hold the Stop button for 5–10 seconds to bypass the low ink warning and resume printing. Important Maintenance Tip
Resetting the software counter does not physically empty the waste ink pads. If you reset the printer multiple times without cleaning or replacing the physical Ink Absorber Pads, ink may eventually leak out of the bottom of the device. For long-term use, it is recommended to eventually wash the pads in warm water and dry them before reinstallation.
To reset a Canon G2010 printer, you can either perform a manual factory reset through the settings menu or enter Service Mode to clear specific errors like the 5B00 (waste ink pad full) error. 1. Simple Factory Reset (Printer Settings)
Use this method to restore original factory settings for general troubleshooting. Turn on the printer.
Press the Setup button (pliers/screwdriver icon); a "1" will appear on the LCD.
Press the + button repeatedly until the letter "C" appears on the LCD. Follow these steps methodically
Press the Color or Black button to start the initialization. 2. Manual Reset for "Waste Ink Pad Full" (Error 5B00)
This process enters Service Mode to clear internal counters without external software. Step A: Enter Service Mode Turn off the printer but keep it plugged in. Press and hold the Power button. While holding Power, press the Stop button 6 times.
Release the Power button. Wait for the green power light to stop flashing and stay steady. Step B: Reset the Counter
While in Service Mode (steady green light), press the Stop button 5 times.
Press the Power button once. The printer will cycle and may print a page showing the D-value (e.g.,
Turn the printer off and back on again to exit Service Mode. 3. Software Resetter Tools If manual steps fail, you can use specialized software:
For the Canon PIXMA G2010, "resetting" typically refers to clearing error codes like P07 or 5B00, which indicate the waste ink counter is full. You can perform a manual reset without external software by following a specific button sequence to enter Service Mode. Manual Reset Procedure (Service Mode)
This process clears the waste ink counter and internal glitches: Enter Service Mode: Turn the printer OFF but leave it plugged in.
Press and hold the Stop button, then press and hold the Power button.
While still holding Power, release the Stop button and press it exactly 6 times.
Release the Power button. The green light should flash and then stay steady, indicating you are in Service Mode. Reset Waste Ink Counter: While in Service Mode, press the Stop button 5 times.
Press the Power button once. The printer may run a quick cycle or print a page to confirm the reset.
Wait for the lights to stop flashing, then turn the printer OFF and back ON again to complete the process. Verifying the Reset (EEPROM Data)
To confirm the reset was successful, you can print the EEPROM data:
In Service Mode, press the Stop button 3 times and then the Power button once.
The printer will print a sheet where the 'D' value represents the waste ink percentage. After a successful reset, this value should be D=000.0. When to Reset
P07 / 5B00 Errors: These are the most common reasons, indicating the "Ink Absorber is Full".
Persistent Glitches: Use a reset if the printer displays persistent paper jam errors even after clearing the paper.
Firmware Issues: If a recent update caused instability, a hardware reset can help revert to a stable state. In summary, resetting the waste ink counter on
For more detailed technical guidance, you can refer to the official Canon G2010 Online Manual
or the Canon IJ Printer Assistant Tool for software-based maintenance.
Are you seeing a specific error code on your printer's display right now? Resetting Canon G2010 Printer: A Simple Guide
Canon PIXMA G2010 , "resetting" typically refers to clearing the Waste Ink Pad Counter (Error Code
), which occurs when the printer's internal absorbers are theoretically full. How to Reset the Waste Ink Counter (Manual Method)
You can often reset the counter without external software by putting the printer into Service Mode Enter Service Mode Turn off the printer. Press and hold the While holding Power, press the button (triangle icon)
Release the Power button. Wait for the green light to stop flashing and stay steady. Reset the Counter
button once to confirm. The printer should print a page showing , indicating a successful reset to 0%.
: Turn the printer off, then back on to resume normal operation. Factory Reset (Settings Initialization)
If you just want to reset all internal settings to factory defaults: Ensure the printer is on and the LCD shows "1". button (pliers/screwdriver icon). button repeatedly until " " appears on the LCD. Press either the button to initialize. ij.manual.canon Third-Party Resetter Tools
If manual steps fail, professional service tools are available, though they may require a paid "Reset Key": WIC Reset Utility
: A popular software used to read and reset waste ink counters. You can download it from WIC Reset Connect Canon Service Tool (V5105 or newer)
: Official-style adjustment software often found on technician forums or sites like wic-reset.com
⚠️ Important Warning:
This procedure resets the printer’s internal counter, not the physical ink pads. If the pads are already full of ink, resetting without cleaning/replacing them can cause ink leakage, damaging your printer or desk.
The difficulty of resetting the G2010 contributes to market stratification. Authorized Canon service centers possess the official reset tools and access to replacement pads. Independent repair shops must rely on leaked or cracked software tools. This enforces a monopoly on the "afterlife" of the printer.
Inside every Canon inkjet printer lies an absorbent pad (or series of sponges) designed to catch excess ink during print head cleaning cycles, borderless printing, and power flushing. Over time, this pad becomes saturated.
Step 1: Download the Utility Go to the official WICReset website (wicresetter dot com). Download the latest version. Avoid third-party download sites that bundle adware.
Step 2: Put the Canon G2010 into Service Mode
Step 3: Run WICReset
Step 4: Exit Service Mode Turn the printer off, wait 10 seconds, then turn it back on normally. Print a test page.
If you cannot find a working resetter printer Canon G2010, or you prefer not to risk software errors, consider these options: