Firstchip Fc1178 Fc1179 Mptools V1052 Free [ POPULAR – CHOICE ]
Use ChipGenius (Windows) or lsusb (Linux) to confirm:
Before downloading software, you must know which chip you have. Using the wrong tool can permanently brick your drive.
If you just want to recover data from an FC1178/1179 drive — do not use MPtools — use recovery software like R-Studio or DMDE instead.
Mastering Flash Drive Repair: FirstChip FC1178/FC1179 MPTools V1.0.5.2 Guide
If you own a budget-friendly USB flash drive that has suddenly become "Write Protected," shows "No Disk," or reports "0MB Capacity," you are likely dealing with a controller issue. Many generic or promotional drives use FirstChip FC1178 or FC1179 controllers.
The FirstChip MPTools V1.0.5.2 is the specialized Mass Production Tool designed to factory-reset these chips and restore your hardware to working order. Here is everything you need to know about using this utility. What is FirstChip MPTools V1.0.5.2?
MPTools (Mass Production Tools) are the "low-level" software used by manufacturers to flash firmware onto USB controllers. Unlike a standard Windows format, this tool communicates directly with the FC1178/FC1179 chipset to: Clear firmware errors and "Read Only" locks. Scan for bad blocks and map them out. Restore the original storage capacity.
Change the Volume Label, Vendor ID (VID), and Product ID (PID). When Should You Use This Tool?
You should look for this specific version if your diagnostic tools (like ChipGenius or Flash Drive Information Extractor) identify your hardware as: Controller: FirstChip FC1178 (or FC1178BC/FC1178S) Controller: FirstChip FC1179
Status: The drive is recognized by the PC but cannot be formatted or accessed. Step-by-Step Recovery Process 1. Identify Your Chipset
Before downloading, run ChipGenius. Ensure the "Controller" field explicitly mentions FirstChip FC1178 or FC1179. If it lists a different brand (like Alcor or Phison), this tool will not work. 2. Download and Extract firstchip fc1178 fc1179 mptools v1052 free
Download the FirstChip MPTools V1.0.5.2 package. Since these tools are often flagged by antivirus software as "false positives" (due to their low-level hardware access), you may need to temporarily disable your real-time protection or run it in a sandbox. 3. Configure the Tool Open the folder and run FirstChip_MpTool.exe.
Insert your corrupted USB drive. It should appear in one of the numbered slots.
Click on Settings (usually requires a blank password or '123456').
In the "Flash Selection" tab, most users should leave it on Auto.
In the "Scan Setting" tab, choose Low Level Format if the drive is severely corrupted, or High Level Format for a quick fix. 4. Run the Repair Click Start or the play button. Warning: This will erase 100% of the data on the drive.
Wait for the progress bar. If it turns Green, your drive is repaired. If it turns Red, the flash memory chip might be physically damaged beyond software repair. Common Error Codes and Fixes
"No Flash Found": Your drive might have a loose connection, or it’s a fake chip that doesn't match the FirstChip database.
"Write Configuration File Error": Try running the application as an Administrator.
"Bad Block Over": The NAND memory inside is too worn out to hold a stable firmware. You can try lowering the capacity manually in settings to bypass the bad sectors.
The FirstChip FC1178/FC1179 MPTools V1.0.5.2 is a powerful "last resort" for fixing dead USB drives. It bypasses OS-level restrictions to reinitialize the hardware. Always ensure you have a backup of your data before attempting a firmware flash, as the process is destructive. Use ChipGenius (Windows) or lsusb (Linux) to confirm:
FirstChip FC1178 and FC1179 chips are widely used in budget-friendly USB flash drives. When these drives experience write protection, capacity loss, or connection errors, the FirstChip MpTools V1052 is the specialized software required to repair and reformat the controller.
This guide provides a comprehensive walkthrough on how to download, set up, and use this specific version of the utility to revive your USB storage device. Understanding FirstChip FC1178 and FC1179
The FirstChip FC1178 and FC1179 are USB 2.0/3.0 flash drive controllers. They are popular among manufacturers for their cost-effectiveness but are prone to firmware corruption if the drive is unplugged incorrectly or during a power surge.
The V1052 version of the Mass Production Tool (MpTools) is specifically optimized to recognize these chipsets and flash the correct firmware to restore factory settings. Prerequisites for Using MpTools
Before starting the recovery process, ensure you have the following ready:
A Windows PC (Windows 7 or 10 is recommended for driver compatibility).
The corrupted USB drive plugged directly into a motherboard USB port (avoid USB hubs). The FirstChip MpTools V1052 software package.
ChipGenius or Flash Drive Information Extractor to verify your controller is indeed an FC1178 or FC1179. How to Use FirstChip MpTools V1052
Verify Your Hardware: Run ChipGenius while your USB is plugged in. Look for "Controller Vendor: FirstChip" and "Controller Part-Number: FC1178" or "FC1179." If the numbers do not match, this tool may not work.
Launch the Software: Extract the V1052 ZIP file and run the executable (usually named FirstChip_MpTools.exe) as an Administrator. MPTools works only on the correct controller family
Detection: Once the interface opens, click the "Refresh" button. Your USB drive should appear in one of the numbered slots. If it doesn't appear, you may need to try a different USB port or check your device manager for "Unknown Device" errors.
Configuration (Optional): Click on "Settings." Usually, no password is required (leave it blank or try "123456"). Here, you can change the Disk Name, Serial Number, or set the drive to "High Level Format" for a quick fix or "Low Level Format" for a deep repair of bad blocks.
The Repair Process: Press the "Start" button on the main screen. The software will begin flashing the firmware and testing the NAND flash memory.
Completion: When the status bar turns green and displays "OK" or "Pass," the process is complete. Unplug the drive and plug it back in to see if Windows recognizes it as a fresh, empty volume. Troubleshooting Common Errors
No Device Found: Try the "Test Mode" method. This involves carefully shorting two pins on the flash chip while plugging it in to force the controller into a programmable state.
Write Fail: This usually indicates the NAND flash memory chips are physically damaged.
Wrong Flash: Ensure you are using the V1052 version, as older versions might not support the specific memory chips attached to your FC1179 controller. Important Safety Note
Using MpTools will permanently erase all data on the USB drive. This tool is a last resort for hardware that is otherwise unusable. Always ensure you have downloaded the software from a reputable firmware archive to avoid malware.
Important Note: MPTools (Mass Production Tool) is used to low-level format, repair, or restore USB drives. This process will permanently erase all data on the drive. There is no undo.
MPTools works only on the correct controller family.
Use ChipGenius (Windows) or lsusb (Linux) to check:
If you see
FC1176,FC1178BC, orCBM2199, this tool will not work.
Do not just click "Start" — configure first: