Anytone At-5555n Ii Service Menu ✓

The method differs slightly depending on the specific firmware version of your radio, but the following method is standard for the N-II series:

Method A (Standard):

Method B (Alternative - if A fails):

Here is a list of the most common parameters you will find in the AT-5555N II service menu. Note: Nomenclature varies slightly between firmware versions 1.0, 1.1, and 2.0.

The Service Menu of the AnyTone AT-5555N II is a powerful diagnostic tool that grants access to the fundamental operational constants of the transceiver. While essential for repair and optimization, it requires a disciplined approach and appropriate test equipment to utilize effectively. Technicians are advised to record the default values of all parameters before making adjustments to ensure the device can be restored to its prior state should an error occur. This paper provides the necessary theoretical framework for safe navigation of this hidden interface.

References AnyTone AT-5555N II Technical Service Manual (Internal Documentation). ARRL Handbook for Radio Communications, Alignment Procedures Chapter.

To access the service menu on the Anytone AT-5555N II , use the following key sequence: the radio. Hold down the buttons simultaneously and turn the radio two seconds

of powering on, release those buttons and quickly press the following sequence in order: (Roger Beep) (Noise Blanker) (Emergency) Important Considerations Calibration Settings

: The service menu contains alignment settings specific to your individual unit. Write down all original values

before making any changes. Improper adjustments can cause permanent frequency drift or hardware issues. RF Gain Fix

: A common use for this menu is to address high "noise floor" readings (where the S-meter shows S5–S7 with no signal). Changing CH-52 (RFG) from its default (often ~86) to a higher value like has been reported to resolve this. Adjustment Method : To change a value, press and hold the PTT button while rotating the Factory Reset

: If the radio becomes unstable, you can perform a full reset by holding while powering on. Google Groups frequency alignment procedures for CW, USB, and LSB modes using this menu?

To access the service menu on the AnyTone AT-5555N II, you must perform a specific sequence of button presses during power-on. This "hidden" menu is primarily used for alignment, such as fine-tuning the frequency or adjusting the Local Oscillator (LO) Google Groups Accessing the Service Menu the radio. Press and hold the button while turning the radio Immediately release and then press the next three buttons in quick succession:

The display should now show service parameters, typically starting with (BFO adjustment) followed by a 3-digit value. Google Groups Navigation and Key Parameters Navigation button to scroll through different settings. Mode-Specific Settings

: Alignment settings may differ depending on your current mode (AM, FM, USB, LSB, CW). Common Parameters : Adjusts the 10.24MHz Beat Frequency Oscillator (BFO).

: Controls the Local Oscillator offset. Experts recommend adjusting this

to get close to the target frequency before fine-tuning with fr0, fr4, fr5, fr9

: Used for fine-tuning specific frequency points (e.g., .00, .04, .05, .09 offsets) by adjusting varicap voltage. Google Groups Factory Reset & Band Expansion Full Reset : If needed, turn the radio on while holding until "RES" then "REND" appears. Frequency Expansion anytone at-5555n ii service menu

: To unlock the radio (e.g., for 11m/CB bands), turn on while holding , then switch from using the channel knob and press to confirm. Google Groups

: Changing values in the service menu without proper test equipment (like a frequency counter or signal generator) can significantly degrade the radio's performance or cause it to operate off-frequency. Google Groups alignment values for SSB or CW modes to help center your frequency? Anytone 5555n Ii Service Menu - Google Groups

Unlocking the Full Potential of Your Anytone AT-5555N II: A Comprehensive Guide to the Service Menu

The Anytone AT-5555N II is a popular and highly-regarded ham radio transceiver that offers a wide range of features and capabilities. However, to truly unlock its full potential, you need to access the service menu. In this article, we'll provide a comprehensive guide on how to access and navigate the Anytone AT-5555N II service menu, as well as explore the various settings and options available.

What is the Service Menu?

The service menu, also known as the "service mode" or "engineering mode," is a hidden menu on the Anytone AT-5555N II that allows users to access and adjust various technical settings and parameters. These settings can help optimize the performance of the radio, troubleshoot issues, and even add new features.

Why Access the Service Menu?

There are several reasons why you might want to access the service menu on your Anytone AT-5555N II:

How to Access the Service Menu

Accessing the service menu on the Anytone AT-5555N II requires a specific sequence of steps:

Navigating the Service Menu

The service menu on the Anytone AT-5555N II is divided into several sections, including:

Common Service Menu Settings and Options

Here are some common settings and options you may find in the service menu:

Important Safety Precautions

When accessing and adjusting settings in the service menu, it's essential to exercise caution and follow proper safety procedures:

Conclusion

The Anytone AT-5555N II service menu provides a wealth of options and settings that can help you optimize the performance of your radio, troubleshoot issues, and add new features. By following the steps outlined in this article, you can access and navigate the service menu with confidence. However, always exercise caution and follow proper safety procedures to avoid causing damage or affecting the performance of your radio. Happy operating! The method differs slightly depending on the specific

Additional Tips and Tricks

FAQs

References

Anytone AT-5555N II Go to product viewer dialog for this item.

, like many advanced radio transceivers, contains a service menu used for factory alignment and calibration. This menu is intended for use by qualified technicians using specialized test equipment such as frequency counters, power meters, and signal generators. Understanding the Service Menu

The service menu allows for the adjustment of internal parameters that are not accessible through the standard user menu. These settings typically include:

Frequency Calibration: Aligning the reference oscillator to ensure the radio transmits and receives on the correct frequency.

Power Levels: Setting the minimum and maximum output power for different modes (AM, FM, SSB).

Modulation Settings: Adjusting the modulation gain to ensure clear audio transmission within legal bandwidth limits.

S-Meter Calibration: Tuning the signal strength indicator for accuracy. Important Considerations

No Factory Reset: Most service menus do not have a "reset to default" option. Changes made are written directly to the EEPROM. If the original values are not recorded before adjustment, it can be very difficult to restore the radio to its factory state.

Regulatory Compliance: Transmitters are calibrated to meet specific legal requirements regarding frequency stability and bandwidth. Improper adjustments can cause the radio to operate outside of legal specifications, potentially causing interference with other services.

Hardware Risks: Making incorrect adjustments to power stages or bias settings can lead to overheating and permanent hardware failure. Recommended Best Practices

For those looking to optimize or repair a radio, it is recommended to:

Consult the Official Service Manual: The manufacturer's service manual provides the exact procedures and required test conditions for alignment.

Use a Dummy Load: Any testing involving transmission should be done into a dummy load to prevent unnecessary interference and protect the final transistors.

Seek Professional Service: If a radio is off-frequency or underperforming, a professional radio shop with the correct calibration tools can ensure the device is set to peak performance safely and legally.

The AnyTone AT-5555N II service menu is a hidden diagnostic and alignment interface used for fine-tuning the radio's hardware parameters, such as frequency offsets and modulation levels. How to Access the Service Menu Method B (Alternative - if A fails):

Because the service menu is intended for technicians, the access sequence must be performed quickly during the startup phase:

Initial Sequence: With the radio off, press and hold the MENU and MODE buttons simultaneously while turning the power on.

Activation: All segments on the LCD will light up for about 2 seconds. Within this window, release the buttons and immediately press these keys in order: RB, NB, SCAN, MEM, and EMG.

Alternative Access: Some versions use a different combination: Turn on while holding FUNC, then quickly press RB, NB, and DW. Key Service Menu Settings

Settings are often displayed as abbreviated codes. It is critical to write down your original values before changing them.

bfC: Adjusts the frequency of the 10.24MHz Beat Frequency Oscillator (BFO).

fr0, fr4, fr5, fr9: Used for fine-tuning frequency steps (voltages across varicaps) for specific frequency offsets (.00, .04, .05, .09).

loC: Controls the local oscillator offset. Adjust this first if the radio is off-frequency on USB or LSB.

IC9 (Modulation): Controls the internal audio/modulation level. Increasing this value (up to 63) can improve transmit audio punch.

CH-52 (RFG): Adjusts the RF Gain calibration; typically set around a default of 86. Common Adjustments & Operations

Frequency Expansion (Unlock): To expand the frequency range (e.g., for 11m/CB use), turn off the radio, press FUNC and EMG while powering on, then use the channel selector to switch between "BAND 1" and "BAND 2" before pressing FUNC to confirm.

Standard Settings: A separate "Background Function Menu" for user settings (like Beep, TOT, or SWR protection) is accessed by holding the MENU button for 2 seconds during normal operation.

Factory Reset: To clear all settings and return to defaults, hold FUNC and SCAN while turning the radio on.

Warning: Improper adjustments in the service menu can cause the radio to transmit out of frequency or damage the final transistors. Ensure you have a frequency counter or calibrated receiver to verify changes. Anytone 5555n Ii Service Menu - Google Groups

Here’s a detailed feature-style article on the AnyTone AT-5555N II Service Menu, written for radio enthusiasts, techs, and CB/Ham operators who want to unlock the full potential of their rig.

If you own an AnyTone AT-5555N II, you already know it’s one of the most feature-packed 10-meter/12-meter radios on the market. But did you know there’s a hidden "Service Menu" that lets you fine-tune everything from transmit power to meter calibration?

Warning: This is not for the faint of heart. Changing these settings can void your warranty, brick your radio, or make it illegal to transmit. Proceed at your own risk.

The AT-5555N II is sold as a 10m/12m amateur radio. The service menu does not add 11m (CB) frequencies—that is controlled by a separate jumper or firmware region lock. The service menu is for calibration only, not band expansion.

Anytone At-5555n Ii Service Menu ✓

2024年10月のジンワン営業カレンダー

東芝D71と言う一体型PCのHDDをSSDに載せ替え